Avery Dennison Power Stacker Provozní pokyny

©2004 Avery Dennison Corp. All rights reserved. 28028 0 Operating InstructionsTC0928OI Rev. AJ 10/12 ®Monarch 928™Stacker 2345678901Fishing Tackle

5. Push the knife toward the printer until the knife does not pivot or rotate. 3. Use the tab to lift the transport and see where the tags are insid

OPERATION AND ADJUSTMENTS 2 This chapter describes how to  make tag adjustments  adjust the belt movement  clear a tag jam  print label strips

Making Tag Adjustments You must adjust the stacker for the width of your tags at the initial stacker setup and whenever you change tag widths. 1. Fee

2. Pull the guide rails (using the end by the bar) out of the grooves at the bottom of the tray. Note: Use two hands to move the guide rails and ho

4. Unlock the tag weight handle by turning the knob counterclockwise. backward Handle 2-4 Operating Instructions 5. Push the handle all the way ba

11. Slide the guide rails into the grooves closest to the tags, except for four-inch wide tags. Make sure the guide rails are all the way forward. Fo

12. Adjust the tag stop to the tag length by moving it up or down. Note: Adjust the tag stop to the length of the regular tags, not the batch separat

Setting the Belt Movement You need to set the belt movement  when you first get the stacker.  when you switch to supplies that have a different th

Adjusting the Belt Movement You need to adjust the belt movement if the tags are stacked too loosely or too tightly. When you see a stacking problem:

Operation and Adjustments 2-9 Loading Supplies If you run out of supplies while printing, the printer shows 756 on the display. 1. Press Feed to fee

Each product and program carries a respective written warranty, the only warranty on which the customer can rely. Avery Dennison Corp. reserves the r

Stacker Full When the stacker is full, a sensor at the end of the tray stops the printer. Sensor The printer shows 761 on the display. 1. Empty the

Clearing a Tag Jam If a tag jams inside the stacker, the printer automatically stops. The printer shows 761 on the display. 1. Check to see if the gu

6. Replace the transport lock handle. Make sure it is completely in the hole at the back of the stacker. Turn the handle down. Lift Here 7. Press Cl

TROUBLESHOOTING 3 This section helps you correct some problems that may occur. Problem Action Stacker Full Empty the tray. Press Clear to clear the

3-2 Operating Instructions Problem Action Tags are not stacking neatly. Adjust the guide rails and tag stop to the width and length of the tags. T

SPECIFICATIONS AThis section lists the product’s specifications. Stacker Height: 14.4 inches (366 mm) Width: 7.9 inches (201 mm) Length: 29.6 inches

A-2 Operating Instructions Supplies Thickness: .007 inches (.18 mm) minimum .010 inches (.25 mm) maximum Widths: 1.2 inch (30 mm) minimum 4.0 inches

28028 0 Avery Dennison170 Monarch LaneMiamisburg, OH 453421-800-543-6650 (In the U.S.A.)1-800-387-4740 (In Canada)www.monarch.com

TOC- i TABLE OF CONTENTS GETTING STARTED... 1-1 Unpacking the Stacke

GETTING STARTED The Monarch® 928stacker works with a Monarch®9855®printer equipped with a Monarch®926knife. 1 The Monarch® 928™ RFID stacker

Unpacking the Stacker After you unpack the stacker, you should have a 928 stacker, stacker mounting plate, and power cord. Installing the Stacker In a

Getting Started 1-3 3. Align the stacker with the front of the knife. 4. Gently lift the stacker and center the guide tabs in the knife opening. 5

1-4 Operating Instructions Connecting the Power Cable To connect the power cable: 1. Turn off the printer. Make sure the stacker’s power switch is

Using Four-inch Wide Tags For four-inch wide tags, nicked corners may occur. You can minimize nicked corners by aligning the knife and stacker properl